Installation and recess requirements

The appliance is designed for flush installation in units with a depth of 635 mm using stainless steel or customer-specific panels. It can also be installed in standard European 610 mm-deep units. Recess dimensions for inset installation are 2029 mm (H) and 451 mm (W); for overlay installation 2032 mm (H) and 457 mm (W). The carcass walls should be at least 16 mm thick, line up flush with the appliance at a depth of at least 102 mm from the outside edge, and have a minimum visible depth of 76 mm.

The adjustable feet are fully retracted at the minimum height. After positioning in the recess, the appliance is raised from the front so it contacts the anti-tipping device. To achieve the minimal plinth panel height of 102 mm, the adjustable feet are raised by 6–8 mm; they can be raised by a maximum of 19 mm for higher plinth panels. Installations behind the appliance are not possible.

Ventilation requirements

Ventilation is provided entirely via the plinth panel. The door panels must close at least 102 mm above the floor and the plinth grill must not be obstructed. Spacers supplied with the appliance must be fitted to separate warm outgoing air from incoming fresh air. Liebherr offers 102 mm high stainless steel plinth panels in widths from 45.7 cm to 182.8 cm as optional accessories.

Door spacing and opening

The appliance must be installed so that doors and handles do not collide with adjacent walls or kitchen elements. A 90° door opening limiter (included in the scope of supply) can be fitted if necessary; the factory setting is 115°. To prevent collisions for a door opening limited to 90°, a minimum spacing of 76 mm from adjoining elements is required. The minimum permitted gap between door panels is 3 mm.

Side-by-Side installation

Monolith appliances can be installed individually, Side-by-Side in a single fitted unit, or Side-by-Side in separate units. A Side-by-Side set is required if the distance between appliances is less than 102 mm. The set includes a sidewall heater, brackets, screws and decorative trim. Using a Side-by-Side set increases energy consumption by 0.4 kWh/24 h for two units and 0.8 kWh/24 h for three units.

IceMaker water connection

Models with IceMaker require a fixed water connection with pressure between 2.8 and 6.2 bar. Only the supply hose delivered with the appliance may be used. A shut-off valve must be installed between the hose line and the mains water supply and must not be positioned behind the appliance. The water quality must comply with local drinking water regulations. The IceMaker is for producing ice cubes in normal household quantities and must only be used with suitable water.

Electrical safety

The appliance must be operated on alternating current with voltage and frequency matching the design for the country of use. Power sockets must be earthed, electrically protected and easily accessible, and must not be located behind the appliance. A separate circuit is recommended. The appliance must not be connected using extension cables, multi-sockets or inverters. Connecting to unearthed sockets or unsuitable devices can lead to electric shock or fire.

Ambient temperature and climate class

The freezer is intended for refrigerating, freezing and storing food and making ice. It has climate class SN-T and is designed for ambient temperatures between 10 °C and 43 °C. It must not be operated outside these temperature ranges.

Secure mounting

To prevent tipping, the anti-tipping device supplied must be secured to the floor or wall at the base of the appliance. After installation, the appliance must be raised until it comes into contact with this device.

Optional accessories

• Flat brushed aluminium handles (various lengths)
• Square brushed aluminium handles
• Round stainless steel handles
• Stainless steel door panels and panel sets
• Stainless steel plinth panels (102 mm high, multiple widths)
• Side-by-Side set with sidewall heater and decorative trim
• Door hinge exchange set (hinge reversal by authorised engineer)
• Water filter (for IceMaker) and FreshAir activated charcoal filters
• Ice cube scoop and ice cube tongs
• Stainless steel care product and cleaner for all Monolith models